| 61.25.1455.575.11.1403 Standard 5 Slewing Ring Bearings | ra max.:4 mm; Calculation factor Y2:1.2; Cb min.:16.5 mm; b:15 mm; d:85 mm; Basic dynamic load rating C:510 kN; rc max.:1 mm; Calculation factor Y1:0.81; l:44.19 mm; r5 min.:1 mm; Calculation factor Y0:0.8; Db min.:169 mm; Mass bearing pair:12.1 kg; C:100.19 mm; d1 ≈:131.37 mm; Basic static load rating C0:570 kN; D:180 mm; Reference speed:2200 r/min; r1,2 min.:4 mm; Calculation factor e:0.83; |
| 162.40.2128.891.41.1503 Standard 5 Slewing Ring Bearings | H:130 mm; Limiting speed:300 r/min; Minimum axial load factor A:58; Da max.:928 mm; Fatigue load limit Pu:1500 kN; Basic dynamic load rating C:4000 kN; d:900 mm; B:39 mm; D1:906 mm; Mass bearing:210 kg; Reference speed:150 r/min; r1,2 min.:5 mm; Basic static load rating C0:27000 kN; D:1060 mm; ra max.:4 mm; d1:1054 mm; da min.:1032 mm; |
| 162.40.2368.891.41.1503 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:114000 N; Oil Speed Rating Open/Shielded n2:4500 rpm; Fillet Radius ra:2.00 mm; Basic Static Radial Load Rating Co:102000 N; B:35.00 mm; Grease Speed Rating Open/Shielded n1:3700 rpm; Accessories:Without Accessories; D:150.0000 mm; d:70.000 mm; |
| 191.20.1400.990.41.1502 Standard 5 Slewing Ring Bearings | Taconite seal (dc shaft position):TER 17; Cap bolt, SAE grade:8; H:125.412 mm; R2:15.875 mm; Initial grease fill:65.205 g; Cap bolt recommended tightening torque:149.1 N·m; End plug (suffix Y):EPR 3; H1:63.5 mm; A1:60.325 mm; Da:90 mm; Max. speed for Taconite seal:1575 r/min; Ca:42.799 mm; RG:1/8 NPT; N1:15.875 mm; Pa:8.9 kN; J max.:177.8 mm; ba:24.606 mm; Stabilizing ring:2 x SR-1608; J min.:165.1 mm; |
| 192.32.2800.990.41.1502 Standard 5 Slewing Ring Bearings | End plug (suffix Y):EPR 9; Da:150 mm; H2:38.1 mm; ba:35.719 mm; R1:53.975 mm; Initial grease fill:110.56 g; R2:22.225 mm; PG:1/8 NPT; Ca:45.796 mm; Housing:SSAFS 517; A1:88.9 mm; h:34.925 mm; Mass pillow block:24.9 kg; H1:95.25 mm; RG:3/8 NPT; Cap bolt:2 x 5/8-11 UNC; Cap bolt recommended tightening torque:298.3 N·m; Max. speed for Taconite seal:1050 r/min; P180°:32 kN; S:4.763 mm; |
| 60.25.1455.500.11.1503 Standard 5 Slewing Ring Bearings | Basic static load rating C0:3050 kN; dk:130 mm; r1 min.:1 mm; Mass plain bearing:6.3 kg; C:55 mm; da min.:98.2 mm; r2 min.:1 mm; Specific dynamic load factor K:100 N/mm²; rb max.:1 mm; b:11.3 mm; ra max.:1 mm; Da max.:143.2 mm; d:90 mm; Sealing solution:Triple-lip seals; α:15 °; Design (sliding contact surface combination):Steel/steel, heavy-d; M:5 mm; b1:11.3 mm; da max.:98.4 mm; Specific static load factor K0:500 N/mm²; |
| 162.28.1600.891.21.1503 Standard 5 Slewing Ring Bearings | Dimension S1:25.4 mm; Distance J:50.8 mm; Weight W:0.61 kg; Basic Static Radial Load Rating Co:15300 N; Basic Dynamic Radial Load Rating:25500 N; Dimension L:96.8 mm; Dimension C:60.3 mm; Dimension F:14.3 mm; Dimension N:10.4 mm; Width A:31.0 mm; Dimension B:157.2 mm; Diameter G:13.5 mm; Distance H:31.8 mm; Pin Dia BS:1/2; Shaft Diameter D:35 mm; Insert Bearing IB:ZMaRC; |
| 162.50.3000.891.41.1503 Standard 5 Slewing Ring Bearings | Stabilizing ring:2 x SR-1518; P90°:72.5 kN; RG:3/8 NPT; A2:206.375 mm; H2:41.275 mm; R2:27.781 mm; Pa:8.1 kN; Cap bolt, SAE grade:5; Ca:49.809 mm; Da:160 mm; Cap bolt recommended tightening torque:149.1 N·m; J min.:260.35 mm; Max. speed for Taconite seal:950 r/min; Cap bolt:2 x 5/8-11 UNC; H:192.484 mm; L:349.25 mm; P150°:40.5 kN; P120°:45.4 kN; A1:98.425 mm; Taconite seal:TER 187; |
| 121.32.3750.990.41.1502 Standard 5 Slewing Ring Bearings | B:7.00 mm; D:22.0000 mm; Sealed Speed Rating n3:23000 rpm; d:7.000 mm; Basic Dynamic Radial Load Rating C:3250 N; Accessories:Two Shields; Basic Static Radial Load Rating Co:1360 N; Grease Speed Rating Open/Shielded n1:36000 rpm; Oil Speed Rating Open/Shielded n2:43000 rpm; Fillet Radius ra:0.30 mm; |
| 61.40.1800.014.29.1503 Standard 5 Slewing Ring Bearings | Oil Speed Rating Open/Shielded n2:11000 rpm; Grease Speed Rating Open/Shielded n1:9000 rpm; Basic Static Radial Load Rating Co:17000 N; Basic Dynamic Radial Load Rating C:22900 N; D:62.0000 mm; Accessories:One Shield; Fillet Radius ra:1.00 mm; d:30.000 mm; B:16.00 mm; |
| 162.45.2654.891.41.1503 Standard 5 Slewing Ring Bearings | Pa:13.8 kN; Cap bolt:2 x 3/4-10 UNC; P60°:119 kN; J max.:333.375 mm; S:4.763 mm; Cap bolt, SAE grade:5; P150°:40 kN; Ca:55.804 mm; da:84.138 mm; End plug (suffix Y):EPR 15; P90°:71.2 kN; A1:111.125 mm; Initial grease fill:181.44 g; R1:58.737 mm; J1:60.325 mm; Da:180 mm; RG:3/8 NPT; N1:22.225 mm; J min.:295.275 mm; H:217.488 mm; |
| 192.20.1600.990.41.1502 Standard 5 Slewing Ring Bearings | Accessories:Shield & Seal; Grease Speed Rating Open/Shielded n1:26000 rpm; Basic Static Radial Load Rating Co:2360 N; d:12.000 mm; Fillet Radius ra:0.30 mm; Basic Dynamic Radial Load Rating C:5070 N; Oil Speed Rating Open/Shielded n2:32000 rpm; D:28.0000 mm; Sealed Speed Rating n3:17000 rpm; B:8.00 mm; |
| 12.45.3400.101.49.1502 Standard 5 Slewing Ring Bearings | d:30 mm; J max.:127 mm; N1:14 mm; N4:4 mm; A1:25 mm; A:40 mm; J min.:108 mm; Recommended diameter for attachment bolts, mm G:12 mm; Fatigue load limit Pu:0.475 kN; N:23.5 mm; H2:17 mm; Thread grub screw G2:M8x1; H:82 mm; Basic dynamic load rating C:19.5 kN; Basic static load rating C0:11.2 kN; Recommended diameter for attachment bolts, inch G:0.5 in; H1:42.9 mm; Housing:SY 506 M/VZ033; Limiting speed:1200 r/min; |
| 161.40.2240.890.11.1503 Standard 5 Slewing Ring Bearings | D:120.0000 mm; Grease Speed Rating Open/Shielded n1:5300 rpm; Accessories:Removable Metal Shie; Sealed Speed Rating n3:3600 rpm; Fillet Radius ra:1.50 mm; Basic Static Radial Load Rating Co:44000 N; B:38.10 mm; Basic Dynamic Radial Load Rating C:62400 N; d:65.000 mm; Oil Speed Rating Open/Shielded n2:6300 rpm; |
| 12.35.2500.001.41.1503 Standard 5 Slewing Ring Bearings | Grease Speed Rating n1:10000 rpm; Oil Speed Rating n2:15000 rpm; B:15.00 mm; Fillet Radius ra:1.00 mm; d:25.000 mm; Basic Dynamic Radial Load Rating C:16800 N; Basic Static Radial Load Rating Co:10400 N; D:52.0000 mm; |
| 61.25.1355.500.11.1503 Standard 5 Slewing Ring Bearings | d3 max.:239.852 mm; d1:184.15 mm; G:199.314 mm; Sleeve:S 3040x7.1/4; d:200 mm; B1:120.396 mm; B:30.429 mm; Threads per inch:8; Mass adapter sleeve assembly:8.85 kg; Hydraulic nut:HMVC 40E; B4:33.35 mm; |