No. | Brand | w | M | K | J | S | H | a | N |
161.36.1900.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
161.28.1600.891.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
161.50.2500.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
12.25.1360.600.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
12.50.3520.001.49.1502 | Standard 5 | - | - | 3 mm | - | - | 28 mm | - | - |
11.30.2031.600.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
162.40.2368.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
61.25.1355.575.11.1403 | Standard 5 | - | - | - | - | - | 80 mm | - | - |
162.40.2368.890.11.1503 | Standard 5 | - | - | - | - | 4.763 mm | - | - | - |
191.50.3150.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
91.30.1607.990.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
92.40.2199.991.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
61.25.1455.575.11.1403 | Standard 5 | - | - | - | - | - | - | - | - |
162.45.2366.890.11.1503 | Standard 5 | - | - | - | 88.9 mm | 0.794 mm | - | 2.381 mm | - |
61.50.2645.001.49.1504 | Standard 5 | - | - | - | - | - | - | - | - |
11.40.2619.001.41.1502 | Standard 5 | - | - | - | 152.4 mm | 0.794 mm | - | 6.35 mm | - |
161.36.1800.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
11.50.3167.001.49.1502 | Standard 5 | - | - | - | - | - | - | - | - |
12.25.1360.601.21.1503 | Standard 5 | - | - | - | - | - | - | - | - |
191.32.3150.990.41.1502 | Standard 5 | - | - | - | - | - | 196.85 mm | - | - |
11.40.3150.001.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
91.25.1310.990.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
162.40.2128.891.41.1503 | Standard 5 | - | - | - | - | - | 130 mm | - | - |
62.25.1355.500.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
91.35.1900.991.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
12.40.2622.400.11.1502 | Standard 5 | - | 6.5 mm | - | - | - | - | - | - |
62.30.1400.000.11.1504 Standard 5 Slewing Ring Bearings | Da max.:525 mm; d:460 mm; r1,2 min.:5 mm; Basic static load rating C0:5850 kN; Mass bearing (including seat washer where applicable):120 kg; D:620 mm; Basic dynamic load rating C:923 kN; Minimum load factor A:180; H:130 mm; Fatigue load limit Pu:95 kN; D1 ≈:466 mm; Reference speed:430 r/min; Limiting speed:600 r/min; d1 ≈:614 mm; ra max.:4 mm; da min.:555 mm; |
12.35.1960.401.41.1503 Standard 5 Slewing Ring Bearings | Mass pillow block:8.62 kg; Max. speed for Taconite seal:1450 r/min; Cap bolt, SAE grade:8; Housing:SAF 309; Taconite seal (dc shaft position):TER 20; Cap bolt recommended tightening torque:149.1 N·m; Ca:45.796 mm; P90°:20.9 kN; N1:19.05 mm; h:32.544 mm; dc:42.875 mm; Cap bolt:2 x 1/2-13 UNC; J min.:187.325 mm; Taconite seal (db shaft position):TER 28; Initial grease fill:39.69 g; Stabilizing ring:SR-11-9; |
92.35.1900.990.11.1502 Standard 5 Slewing Ring Bearings | Grease:1.590 kN; D:150 mm; with tapered bore:2314 ; B:51 mm; rs Dynamic (Cr):2.1 mm; Static (Cor):112.270 kN; with cylindrical bore:4 500 min-1; Oil:3 800 min-1; Pu:37.600 kN; d:70 mm; B1:mm; |
162.28.1600.890.11.1503 Standard 5 Slewing Ring Bearings | d:55 mm; B:35 mm; Mass inner ring:0.12 kg; r, r1,2 min.:0.6 mm; F:60 mm; |
162.45.2366.890.11.1503 Standard 5 Slewing Ring Bearings | L:117.475 mm; A6:19.05 mm; J:88.9 mm; N1:14.287 mm; Basic dynamic load rating C:73.8 kN; A5:27.781 mm; Attachment bolt diameter G:12.7 mm; d2:62.706 mm; Limiting speed:5100 r/min; s:25.4 mm; a:2.381 mm; da:36.513 mm; S:0.794 mm; B:69.85 mm; Mass bearing unit:3.27 kg; A:57.15 mm; A1:72.231 mm; |
12.25.1360.600.11.1503 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:11200 N; Distance J:69.9 mm; Diameter N:11.5 mm; Dimension L:95.3 mm; Height T:38.9 mm; Shaft Diameter D:25 mm; Insert Bearing IB:Stainless Steel; Dimension DA:74.6 mm; Dimension A2:13.5 mm; Dimension A1:29.4 mm; Basic Static Radial Load Rating Co:7800 N; |
62.40.1700.007.19.1503 Standard 5 Slewing Ring Bearings | da:50.8 mm; Basic dynamic load rating C:84.5 kN; A:57.15 mm; s:25.4 mm; a:2.381 mm; Mass bearing unit:4.99 kg; J:111.125 mm; B:73.025 mm; A1:75.406 mm; A6:19.05 mm; S:0.794 mm; A5:27.781 mm; Limiting speed:4100 r/min; d2:73.819 mm; N1:14.287 mm; L:139.7 mm; Attachment bolt diameter G:12.7 mm; |
161.36.2000.891.41.1503 Standard 5 Slewing Ring Bearings | d:44.45 mm; GN:1/4-28 SAE-LT; Limiting speed:4300 r/min; Housing material:Cast iron; J:148.5 mm; Basic dynamic load rating C:33.2 kN; Basic static load rating C0:21.6 kN; s1:32.7 mm; R1:24.5 mm; Recommended diameter for attachment bolts, inch G:0.5625 in; J6:120.5 mm; B1:43.7 mm; DN:6.5 mm; Db2:111 mm; Recommended tightening torque for grub screw:16.5 N·m; Da:98.4 mm; Thread grub screw G2:3/8-24 UNF; |
92.40.2003.990.11.1502 Standard 5 Slewing Ring Bearings | A2:317.5 mm; Initial grease fill:3515.4 g; Cap bolt recommended tightening torque:4284.4 N·m; Bearing limiting speed:1500 r/min; ba:103.188 mm; Stabilizing ring:SR-0-40; L:869.95 mm; R1:163.512 mm; Cap bolt, SAE grade:8; End plug (suffix Y):EPR 21; da:182.563 mm; Mass pillow block:441 kg; A1:228.6 mm; H:495.3 mm; Cap bolt:4 x 1 1/2-6 UNC; RG:1 NPT; Labyrinth ring:2 x LOR 665; P120°:249 kN; |
91.50.2446.990.41.1502 Standard 5 Slewing Ring Bearings | L:137 mm; N:16 mm; Recommended diameter for attachment bolts, mm G:14 mm; N4:4 mm; d:45 mm; s1:26.5 mm; J:105 mm; Recommended tightening torque for grub screw:7.4 N·m; A1:14 mm; J7:33.5 mm; Db1:102 mm; Basic static load rating C0:21.6 kN; Db2:112 mm; Hexagonal key size for grub screw N:3 mm; Recommended diameter for attachment bolts, inch G:0.5625 in; Limiting speed:850 r/min; B1:44 mm; Fatigue load limit Pu:0.915 kN; |
192.25.2800.990.41.1502 Standard 5 Slewing Ring Bearings | Bearing limiting speed:5300 r/min; End plug (suffix Y):EPR 11; H2:41.275 mm; Initial grease fill:286.33 g; Cap bolt, SAE grade:5; A1:98.425 mm; P150°:34.7 kN; Da:160 mm; Mass pillow block:21.3 kg; PG:1/8 NPT; J1:53.975 mm; L:349.25 mm; H1:101.6 mm; N1:19.05 mm; Pa:8.1 kN; Ca:49.809 mm; J min.:263.525 mm; da:82.55 mm; P180°:42.3 kN; Housing:FSAF 518; |
92.50.2446.990.41.1502 Standard 5 Slewing Ring Bearings | db min.:39.6 mm; ra max.:1 mm; Mass bearing:0.15 kg; Db max.:60 mm; Calculation factor f2C:1.05; D1:53.3 mm; d:35 mm; D:62 mm; Da max.:57.4 mm; Preload class D GD:480 N; Ball diameter Dw:7.938 mm; rb max.:0.3 mm; d1:43.7 mm; Preload class B GB:120 N; Attainable speed for grease lubrication:24000 r/min; Calculation factor f1:1; Basic dynamic load rating C:15.6 kN; Fatigue load limit Pu:0.4 kN; r3,4 min.:0.3 mm; |
92.35.2012.990.11.1502 Standard 5 Slewing Ring Bearings | r1 min.:0.6 mm; Da max.:94.7 mm; B:55.55 mm; b1:8 mm; b:9 mm; Specific static load factor K0:300 N/mm²; Sealing solution:Triple-lip seals; da min.:68.3 mm; Lubricant:Regular relubricatio; Specific dynamic load factor K:100 N/mm²; dk:91.186 mm; M:6.5 mm; Basic static load rating C0:1040 kN; D:100.013 mm; α:6 °; C:47.625 mm; Basic dynamic load rating C:345 kN; rb max.:1 mm; Mass plain bearing:1.85 kg; |
62.50.2800.001.49.1504 Standard 5 Slewing Ring Bearings | Misalignment factor k1:0.099; d1:65 mm; Da max.:121 mm; Ba min.:12 mm; Basic dynamic load rating C:196 kN; d2 ≈:88.5 mm; r1,2 min.:1.5 mm; Reference speed:4800 r/min; s1 max.:9.6 mm; ra max.:1.5 mm; Limiting speed:6700 r/min; db min.:80 mm; da max.:98.3 mm; Fatigue load limit Pu:24 kN; D1 ≈:116 mm; Mass bearing + sleeve:2.3 kg; Basic static load rating C0:208 kN; Operating clearance factor k2:0.127; |
162.40.2368.891.41.1503 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:114000 N; Oil Speed Rating Open/Shielded n2:4500 rpm; Fillet Radius ra:2.00 mm; Basic Static Radial Load Rating Co:102000 N; B:35.00 mm; Grease Speed Rating Open/Shielded n1:3700 rpm; Accessories:Without Accessories; D:150.0000 mm; d:70.000 mm; |
161.40.2128.890.11.1503 Standard 5 Slewing Ring Bearings | Comparative axial load rating CFa:344 kN; Basic static load rating C0:19300 kN; Calculation factor e:0.37; Calculation factor Y1:1.8; Comparative radial load rating CF:1830 kN; d1 ≈:760 mm; Fatigue load limit Pu:1340 kN; D:914.4 mm; Mass bearing:600 kg; Calculation factor Y0:1.8; T:390 mm; Design variant/feature:TQON/GW; r1,2 min.:3.3 mm; r3,4 min.:6.4 mm; B:390 mm; Thrust factor K:1.54; Basic dynamic load rating C:7650 kN; |
91.35.1900.991.41.1502 Standard 5 Slewing Ring Bearings Video