| 61.25.1355.575.11.1403 Standard 5 Slewing Ring Bearings | d1 ≈:596 mm; Da max.:541 mm; Fatigue load limit Pu:57 kN; Minimum load factor A:67; Reference speed:560 r/min; D1 ≈:504 mm; da min.:559 mm; D:600 mm; Mass bearing (including seat washer where applicable):47 kg; ra max.:2 mm; Limiting speed:800 r/min; Basic static load rating C0:3600 kN; r1,2 min.:2.1 mm; H:80 mm; Basic dynamic load rating C:553 kN; d:500 mm; |
| 191.20.1600.990.41.1502 Standard 5 Slewing Ring Bearings | d:65 mm; da max.:76 mm; Limiting speed:3600 r/min; Mass bearing:1.75 kg; B:38.1 mm; Da max.:111 mm; Fatigue load limit Pu:3.1 kN; Calculation factor Y2:1.24; Calculation factor X:0.63; D2 ≈:110.65 mm; Calculation factor Y0:0.66; Calculation factor Y1:0.78; r1,2 min.:1.5 mm; d2 ≈:77.5 mm; Basic static load rating C0:73.5 kN; Calculation factor e:0.8; ra max.:1.5 mm; D:120 mm; a:71 mm; da min.:74 mm; |
| 192.50.3150.990.41.1502 Standard 5 Slewing Ring Bearings | B:160 mm; Basic dynamic load rating C:3150 kN; r2 min.:3 mm; ra max.:1 mm; Specific dynamic load factor K:80 N/mm²; b:21 mm; M:8 mm; Basic static load rating C0:4750 kN; D:460 mm; α:3 °; da max.:366 mm; d:340 mm; da min.:348 mm; Specific static load factor K0:120 N/mm²; rb max.:3 mm; Da min.:391 mm; Material constant KM:1055; b1:21 mm; Da max.:446 mm; Design (sliding contact surface combination):Steel/PTFE FRP; |
| 281.30.1300.013 Type 110/1500.1 Standard 5 Slewing Ring Bearings | R1:101.6 mm; A2:260.35 mm; Stabilizing ring:SR-28-0; Cap bolt:4 x 3/4-10 UNC; A1:149.225 mm; RG:3/8 NPT; Eye bolt:3/8-16 UNC; Cap bolt recommended tightening torque:515.2 N·m; Cap bolt, SAE grade:8; H:298.45 mm; Max. speed for Taconite seal:625 r/min; da:122.237 mm; P90°:116 kN; P120°:73.8 kN; N1:28.575 mm; S:4.763 mm; Initial grease fill:850.5 g; R2:30.163 mm; Mass pillow block:90.3 kg; |
| 161.40.2368.891.41.1503 Standard 5 Slewing Ring Bearings | Fatigue load limit Pu:0.28 kN; Recommended tightening torque for grub screw:4 N·m; s1:18.3 mm; H:89 mm; B:31 mm; Limiting speed with shaft tolerance h6:5000 r/min; H2:36 mm; Grub (set) screw G2:1/4-28 UNF; H1:76 mm; Hexagonal key size for grub screw N:3.175 mm; A1:12 mm; Housing material:Composite for food a; G1:21 mm; A5:20.3 mm; A2:24.5 mm; A:27.5 mm; Mass bearing unit:0.35 kg; G:M16; Basic static load rating C0:6.55 kN; |
| 162.36.2000.890.11.1503 Standard 5 Slewing Ring Bearings | Mass inner ring:0.059 kg; d:30 mm; F:35 mm; B:30 mm; r, r1,2 min.:0.3 mm; |
| 11.35.2220.000.11.1503 Standard 5 Slewing Ring Bearings | Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; Specific dynamic load factor K:10 N/mm²; Specific static load factor K0:20 N/mm²; d:4 mm; D:8 mm; Permissible sliding velocity v min.:0.25 m/s; Mass bushing:0.001 kg; Coefficient of friction µ min.:0.05; B:4 mm; Tolerance shaft:h8; Coefficient of friction µ max.:0.1; |
| 61.40.1400.001.29.1504 Standard 5 Slewing Ring Bearings | Accessories:Two Seals; D:47.6000 mm; d:22.200 mm; Fillet Radius ra:0.79 mm; Oil Speed Rating Open/Shielded n2:17000 rpm; Basic Dynamic Radial Load Rating C:10100 N; Shielded or Sealed B1:12.7 mm; Basic Static Radial Load Rating Co:5850 N; Grease Speed Rating Open/Shielded n1:14000 rpm; Width Plain B:9.5 mm; Sealed Speed Rating n3:9600 rpm; |
| 162.50.2800.891.41.1503 Standard 5 Slewing Ring Bearings | rb max.:1 mm; Basic dynamic load rating C:425 kN; Da min.:79 mm; d:57.15 mm; M:4 mm; Specific static load factor K0:300 N/mm²; b1:5 mm; da max.:65.2 mm; r1 min.:0.6 mm; B:50.013 mm; dk:82.169 mm; r2 min.:1 mm; C:42.85 mm; Da max.:85.3 mm; Specific dynamic load factor K:150 N/mm²; Basic static load rating C0:850 kN; D:90.488 mm; Sealing solution:Triple-lip seals; Lubricant:Maintenance free &nd; |
| 192.32.3150.990.41.1502 Standard 5 Slewing Ring Bearings | Sealing solution:Triple-lip seals; d:100 mm; Lubricant:Regular relubricatio; Mass plain bearing:5.9 kg; rb max.:1 mm; r1 min.:1 mm; r2 min.:1 mm; M:5 mm; C:55 mm; da max.:111.2 mm; D:160 mm; da min.:108.1 mm; B:85 mm; Specific dynamic load factor K:100 N/mm²; Da max.:153.3 mm; Material constant KM:330; Specific static load factor K0:500 N/mm²; b:11.5 mm; ra max.:1 mm; Basic dynamic load rating C:655 kN; |
| 11.50.3747.001.49.1502 Standard 5 Slewing Ring Bearings | Taconite seal:TER 24; R2:15.875 mm; Mass pillow block:8.04 kg; Stabilizing ring:SR-11-9; J min.:187.325 mm; Max. speed for Taconite seal:1575 r/min; Cap bolt:2 x 1/2-13 UNC; L:244.475 mm; A1:69.85 mm; ba:25.4 mm; H2:23.813 mm; P90°:27.1 kN; H1:69.85 mm; R1:34.131 mm; Pa:3.47 kN; Da:100 mm; h:31.75 mm; S:4.763 mm; H:133.35 mm; A2:171.45 mm; |
| 60.25.1455.575.11.1403 Standard 5 Slewing Ring Bearings | Cap bolt recommended tightening torque:1220 N·m; ba:56.356 mm; N1:25.4 mm; Labyrinth ring:2 x LOR 125; P150°:68.1 kN; Da:225.001 mm; Pa:25.4 kN; End plug (suffix Y):EPR 16; Initial grease fill:382.73 g; A1:133.35 mm; Stabilizing ring:2 x SR-0-21; R2:36.513 mm; PG:1/4 NPT; P180°:84.5 kN; R1:79.375 mm; P120°:73.8 kN; Bearing limiting speed:3200 r/min; P60°:189 kN; Appropriate attachment bolt size G:0.875 in; |
| 11.30.1440.190.11.1503 Standard 5 Slewing Ring Bearings | r, r1,2 min.:1 mm; F:72 mm; d:65 mm; Mass inner ring:0.14 kg; B:25 mm; |
| 11.40.3150.000.11.1502 Standard 5 Slewing Ring Bearings | Calculation factor e:0.3; D:1360 mm; Da max.:1332 mm; Calculation factor Y2:3.4; Reference speed:20 r/min; r1,2 min.:7.5 mm; B:412 mm; Limiting speed:35 r/min; Calculation factor Y1:2.3; D1 ≈:1230 mm; Mass bearing:1875 kg; Basic dynamic load rating C:18228 kN; d2 ≈:1076 mm; Fatigue load limit Pu:2240 kN; d:950 mm; Calculation factor Y0:2.2; ra max.:6 mm; Basic static load rating C0:38000 kN; |
| 12.25.1360.600.11.1503 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:11200 N; Distance J:69.9 mm; Diameter N:11.5 mm; Dimension L:95.3 mm; Height T:38.9 mm; Shaft Diameter D:25 mm; Insert Bearing IB:Stainless Steel; Dimension DA:74.6 mm; Dimension A2:13.5 mm; Dimension A1:29.4 mm; Basic Static Radial Load Rating Co:7800 N; |
| 91.40.2395.990.11.1502 Standard 5 Slewing Ring Bearings | D1:154 mm; r1,2 min.:2.1 mm; D:250 mm; B:20.5 mm; Mass housing washer:5.06 kg; |